JUMO safetyM TB/TW Temperature limiter, temperaturemonitornach DIN EN 14597B 70.1160.0Operating Instructions2014-06-12
3 Mounting and removal2014-06-1283 Mounting and removalThe instrument is clipped onto a 35 mm DIN rail (EN 60715) from the front.h Insert a screwdriv
3 Mounting and removal92014-06-123.1 Mounting location3.2 Close mounting3.3 Electrical isolationaPreferably vibration-free, so that screw terminals ca
4 Electrical connection2014-06-12104 Electrical connection4.1 Installation notesAThe instrument is fitted with electronic components that can be destr
4 Electrical connection112014-06-124.2 Connection diagramScrew terminals are used for connecting strands with a cross-section of 0.2 to 2.5mm2.AC supp
4 Electrical connection2014-06-1212Supply as on nameplateACL1 External conductorN Neutral conductorDCL+L-Analog inputs Thermocouple /double thermocou
4 Electrical connection132014-06-12Analog inputs 0 to 20 mA4 to 20 mA (evaluated for temp. Limiter)0(2) to 10 VBinary input for connection to floating
5 Commissioning the instrument2014-06-12145 Commissioning the instrument5.1 Displays and controlsh Apply the supply voltage, all segments light up fo
5 Commissioning the instrument152014-06-125.2 Display after switch-onv The value to be displayed is adjustable, as in Chapter 7.6 “C116 Display after
5 Commissioning the instrument2014-06-12165.4 Canceling editing + will cancel editing, the original value is retained.5.5 Acknowledging alarms (for
5 Commissioning the instrument172014-06-12
Overview of operationC111...C122 see Chapter 7 “Configuration level”MeasuredvalueDifferential2whenC116 = 1whenC116 = 2Warningalarm1Limit valuewhenC116
6 Parameter level2014-06-12186 Parameter levelThis level is where to find the parameters AL, VA, ALD and DF, which are freely accessible to operating
7 Configuration level192014-06-127 Configuration levelAll the configuration level parameters C111 - C122 are listed in the table below. Parameters tha
7 Configuration level2014-06-12207.1 C111 Analog inputsAnalog input CommentSetting range for AL: (can be restricted via setup)Limits foroverrange/unde
7 Configuration level212014-06-12If the system is in the OK range, the relay is active and LED K1 shows green.If the system leaves the OK range, the r
7 Configuration level2014-06-1222kFactory setting037W3Re-W25Re D Thermocouple -1999 to +9999°C -5 to +2500°C039Cu-CuNi T Thermocouple EN 60584 -1
7 Configuration level232014-06-127.2 C112 Setting for a double thermocouple7.3 C113 Unit, decimal place7.4 C114 Device functionDouble thermocouple Com
7 Configuration level2014-06-12247.5 C115 Switching actionSwitching actionComment0 inverse If limit value AL is exceeded, the fitted relay switches OF
7 Configuration level252014-06-121 direct If the value falls below limit AL, the fitted relay switches OFF. LED K1 shows red and the limit flashes in
7 Configuration level2014-06-12267.6 C116 Display after switch-on7.7 C117 Binary input functionk Factory settingNormal display Comment0 Limit value Ch
7 Configuration level272014-06-127.8 C118 Display switch-off after timeout7.9 C119 Warning alarm functionThe warning alarm is indicated via LED KV and
Contents Overview of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7 Configuration level2014-06-12287.10 SCL, SCH, AL LO, AL HI, OFFS, HYST1, HYST27.11 C 120 Limit value for relay switching operationsFunction Comment
7 Configuration level292014-06-127.12 C 121 Count for relay switching operations7.13 C 122 Operating hours counterMeaningValue range(factory setting i
8 Technical data2014-06-12308 Technical data8.1 Analog inputsResistance thermometersThermocouplesDesignation Measuring range Accuracy1Pt 100 EN 60751
8 Technical data312014-06-12DC voltage, DC currentNiCrSi-NiSi N EN 60584 -100 to +1300°C 0.4%Pt10Rh-Pt S EN 60584 0 to +1768°C 0.4%Pt13Rh-Pt R EN 6
8 Technical data2014-06-12328.2 Measuring circuit monitoringRTD temperature probeand KTY11-6Twin thermocouples Thermocouples Current 0 to 20 mA, 4 to2
8 Technical data332014-06-128.3 Binary input8.4 Binary outputs8.5 Supply8.6 Test voltages to EN 60730, Part 1Connection Function1 floating contact Con
8 Technical data2014-06-12348.7 Electrical safety8.8 Environmental influences Clearances / creep pathsMains to electronic components and probe≥ 6 mm /
8 Technical data352014-06-128.9 Housing 8.10 Approvals/MarksMaterial polyamide (PA 6.6)Screw terminal 0.2 to 2.5mm2 screw terminalMounting on 35mm x 7
9 DIN-approved probes2014-06-12369 DIN-approved probes 9.1 Probes for operation in airNote: Because of the high response accuracy, the use of thermowe
9 DIN-approved probes372014-06-129.2 Probes for operation in water and oil901006/66-953-1046-6-250-668/000 90.027 1 x PT30Rh-PT6Rh, TypE „B“ 600 ... 1
Contents7.1 C111 Analog inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 DIN-approved probes2014-06-1238Note: Because of the high response accuracy, only use thermowells (pockets) that are included in the scope of deliver
9 DIN-approved probes392014-06-129.3 Probes for operation in air, water and oilASensor short circuit can only be detected with a double thermocouple.N
9 DIN-approved probes2014-06-1240
10 Setup program412014-06-1210 Setup programThis program and the interface with adapter can be supplied asaccessories. They offer the user the followi
10 Setup program2014-06-124210.3 Activating the access codeThe factory setting is for no level inhibit to be active in the instrument.The access code
11 Alarm messages432014-06-1211 Alarm messagesThe following alarm messages can be shown in alternation with the temperature display:Alarm display Caus
12 Error messages2014-06-124412 Error messagesError display (code) Cause RemedyThe total number of relay switching operations has been reached.h Incre
12 Error messages452014-06-120008 reserved -0009 Calibration data checksum The instrument must be returned to JUMO for repair.h Send the instrument in
13 What if...2014-06-124613 What if...Description Cause RemedyThis appears on thedisplay:The Setup program is transferring data.The monitoring functio
13 What if...472014-06-12Description Cause RemedyRelay contact betweenterminals 9, 10 or 9, 12does not switch.- The fitted safety fuse in the pole ar
Contents9.1 Probes for operation in air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
13 What if...2014-06-1248
JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.Street address:Moritz-Juchheim-Straße 136039 Fulda, GermanyDelivery address:
1 Brief description2014-06-1241 Brief descriptionTemperature limiters (TB) and temperature monitors (TW) are used to monitor thermal processes in syst
2 Identifying the instrument version52014-06-122 Identifying the instrument versionThe nameplate is glued to the side of the housing.The supply volta
2 Identifying the instrument version2014-06-126Basic type701160Temperature limiter (TB) / temperature monitor (TW)Version8 factory setting9 configurat
2 Identifying the instrument version72014-06-122.2 Scope of delivery-JUMO safetyM TB/TW in the ordered version- 1 Operating Instructions 701160.0045 P
Commentaires sur ces manuels