Jumo 705040 mTRON T - Router Module Installation Instru Manuel d'utilisateur

JUMO mTRON TMeasuring, Control, and Automation SystemRouter ModuleB 705040.4Installation Instructions2014-05-06/00548130

1 Introduction101.3.4 DisposalDisposing of the deviceDisposing of the packaging materialThe entire packaging material (cardboard packaging, inserts, p

111 Introduction1.4 Identifying the device version1.4.1 NameplatesPositionThe nameplate (B) is affixed to the module case.An additional nameplate with

1 Introduction12Fabrication no. (F-Nr)Among other things, the fabrication number contains the date of production (year/week).Example: F-Nr = 007003380

131 Introduction1.5 Brief descriptionThe router module is used to achieve decentralization within the automation system, whichmeans that the input/out

1 Introduction141.6 LED displays"P" LED (Power)The LED is permanently lit in green if the module is being supplied with voltage."S"

151 Introduction1.6.2 System states and errorsThe following table lists all the system states and errors that are indicated by the "S" LED (

1 Introduction16

172 Mounting2.1 General information on installation/dismountingMounting siteAll modules have protection type IP20 and are only intended for use in fir

2 Mounting18Minimum distances2.2 Installation/dismounting on DIN railAll modules in the system are intended for installation on a DIN rail according t

192 Mounting2.2.1 Special modulesInstallation, using the example of a router module 705040Procedure:Step Activity1 Mount the router module (A) in the

2 Mounting20Dismounting, using the example of a router module 705040Removing the router module from the DIN railProcedure:(A)(B)(A3)(B2)Step Activity1

212 Mounting4 Move the router module (A) to the left (A3) until the side contacts on the right side of the router module are exposed.5 Insert a suitab

2 Mounting222.3 Replacing module inserts2.3.1 Special modulesReplacing the module insert of a router module 705040For service purposes, the case (D) c

232 MountingMounting the module insertStep Activity1 Affix the new nameplate in place of the old nameplate (C) in the case.2 Hold the new module inser

2 Mounting242.4 Dimensions22.56.6103.6101101.594.517.6

253 Electrical connection3.1 Installation notesRequirements for the personnel• Work on the modules must only be carried out to the extent described an

3 Electrical connection26References to other information• The electromagnetic compatibility meets the standards and regulations cited in the techni-ca

273 Electrical connection3.3 Connection diagram3.3.1 Display and connection elementsCAUTION!At maximum load, the temperature at the "+24 V"

3 Electrical connection283.3.2 Interfaces3.3.3 Voltage supplyConnection Designation Connection elementSystem bus In (input) Bus In 1 TX+ transmit dat

293 Electrical connection3.4 Functional testOnce the electrical connection is complete, the following points must be checked:1) Voltage supply 2) Conn

3Contents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51.1 Available tec

3 Electrical connection30

314 Appendix4.1 Technical data4.1.1 Interfaces4.1.2 Electrical dataBus In (system bus)Application For connection of a base unit, a router module or a

4 Appendix324.1.3 Case and ambient conditions4.1.4 Approval/approval marksCase type Plastic case for DIN rail mounting in the control cabinet (indoor

JUMO GmbH & Co. KGStreet address:Moritz-Juchheim-Straße 136039 Fulda, GermanyDelivery address:Mackenrodtstraße 1436039 Fulda, GermanyPostal addres

Contents43.3.3 Voltage supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

51 Introduction1.1 Available technical documentationThe documents specified below are available for the measuring, control, and automation sys-tem.1.1

1 Introduction61.1.4 Special modules1.1.5 Operating, visualization, recording1.1.6 Power supply unitsProduct Type of documentation No. Printed PDF fil

71 Introduction1.2 Safety information1.2.1 Warning symbols1.2.2 Note signsDANGER!This symbol indicates that personal injury caused by electrical shock

1 Introduction81.2.3 Intended useThe modules described are intended for measuring, control, and automation tasks in an indus-trial environment, as des

91 Introduction1.3 Acceptance of goods, storage, and transport1.3.1 Checking the delivery• Ensure that the packaging and contents are not damaged • Ch